ABS and PVC pipes are used in the construction industry.
ABS and PVC are two types of plastic-based pipes and fittings used in the construction industry. Both types are used in limited-pressure applications such as DWV (drain, vent and waste) and sewer lines. ABS and PVC types have smooth inner surfaces that are ideal for unimpeded flow, and the pipes' strength and chemical resistance ensures much-needed durability for sewer installations. The pipes can withstand years of withering without any sings of corrosion, rust or rot or any other form of material degradation.
Material
The core material in ABS pipes and fittings is a thermoplastic resin known as acrylonitrile butadiene styrene, or ABS for short. The pipes have a foam core, and the edge of each piece of pipe needs to be glued less than 1 inch for it to maintain resistance against high pressure. PVC pipes, also known as CPVC, are made from a thermoplastic material known as chlorinated poly-vinyl chloride. The main structural difference between the two types is that ABS as a material is more flexible than PVC, and can deform under sun exposure.
ABS Uses
ABS pipes are extensively used in DWV applications, and more than 10 billion feet of the material have been installed by constructors in residential and commercial structures. ABS is used in both ground and above-ground applications, and may also be installed outdoors, provided the pipes meet certain conditions. Based on local regulations, outdoor usage may require the pipes to contain pigments to prevent it from ultraviolet radiation or to be painted with a water-based latex paint.
PVC Uses
PVC pipes are most suited to distribute water across a range of temperatures. At room temperatures, the pipes have a 400 psi (pounds per square inch) pressure rating, and at 180 F, the pressure rating is 100 psi. PVC pipes are resistant to most common household chemicals, and since the material does not support combustion and cannot burn without a fuel source, it is used as an alternative to traditional steel and copper-based pipes in sprinkler installations.
Markings
Both ABS and PVC pipe types are required by regulatory bodies to contain physical markings on the body. Even if the pipes are cut in relatively small pieces, the markings must be clearly visible on the surface; some local regulations mandate that the markings appear in every 5 feet of pipe length. Along with manufacturer's name and trademark, the marks contain information about conformance to standards, size, type of resin and schedule number. Markings for pressure ratings are included in PVC pipes but is absent in ABS pipes, whereas a DWV identification is included in ABS pipes but absent in PVC pipes.
Installation
Installing ABS pipes are simpler than installing PVC pipes, because the former is a one-step process whereas the latter involves two steps. In PVC installation, a purple primer must be applied before gluing together each joint, otherwise they will tear apart over time. Using purple primer is an involved and tedious process because the subtance is very viscous and can easily spread, making the piping look unprofessional. Another drawback of PVC installation is that joints must be held together for 5 to 10 seconds after applying glue, otherwise the joints will be undone; in ABS installation, the glue works right away and the joints don't have to be held together.
Related Posts:
Use Solderless Copper Pipe Fittings
Copper pipe is used in water systems in most homes to carry hot and cold water throughout the house. Traditionally, copper pipes have been joined with solder connections.These are made by putting...
Cut Galvanized Steel Pipe
Cut Galvanized Steel PipeA variety of pipes in older homes may be made of galvanized steel. Today, most pipes used are made out of polyvinyl chloride (PVC). To replace these old galvanized pipes,...
Install A Furnace Flue Pipe
Install a Furnace Flue PipeNatural gas furnaces are efficient appliances and widely used to heat homes. When burning a fuel for combustion, that combustion gas must be carried outside. Furnace flu...
Cut Pex Pipe
Cutting PEX PipePEX pipe, made by Zurn, has made plumbing easier for the average homeowner by providing a product that is both easy to install and easy to cut. No special tools are required to cut...
What Is A Pvc Spigot Fitting
A PVC spigot is used to connect pipes to a faucet.Poly vinyl chloride, or PVC, is a material manufactured for applications such as pipe systems for residential and industrial settings. PVC is stro...
